HK Macau Stepwgn Club - Powered by Discuz! Board

標題: Can 18x8.5 ET55 wheels fit RK1? [打印本頁]

作者: Wongjas 時間: 27-8-2013 00:25 標題: Can 18x8.5 ET55 wheels fit RK1?

如題。謝謝師兄。

BTW, what size of tyres to run. 225/40/18?

Rgds,
Jason

作者: cliffchow 時間: 27-8-2013 08:19

如題。謝謝師兄。

BTW, what size of tyres to run. 225/40/18?

Rgds,
Jason
Wongjas 發表於 2013-8-27 00:25

In general, it is recommended 7-7.5j 48-52 offset for the spec for rims. The size of tyres is quite personal. 225/40/18 is not a bad choice.

作者: sammykwan 時間: 27-8-2013 10:35

18x8.5 ET55, may I know what model of wheel is that?

作者: Wongjas 時間: 27-8-2013 16:42

Its original rims of Subaru Sti.

Btw, I have just installed already at 精藝 today. It's so far perfect.

I got Much stronger steering (previously its quite loose)

Its perfect match with my rsr basic I suspension now, personally feel much more comfortable and 服好多 (previously 用16寸呔感覺好拋好long and 好林, 避震機同條林呔好似 damping effect 一齊拋到暈船浪咁

Will update fuel consumption later and maybe possible to upload photos

作者: sammykwan 時間: 27-8-2013 17:52

Its original rims of Subaru Sti.

Btw, I have just installed already at 精藝 today. It's so far perfect.

I got Much stronger steering (previously its quite loose)

Its perfect match with my rsr basic ...
Wongjas 發表於 27-8-2013 16:42

good to know that there is no rubbing at the inner fender...have you tried to turn all the way both to left and to right?

作者: victor 時間: 27-8-2013 18:57

無low低可能好D

作者: Wongjas 時間: 27-8-2013 19:42

It's a bit tricky here. Indeed, it was my concerns too.

With ET55 and 8.5J, they have a 3mm spacer install to avoid rubbering and suspension.
All the way right and left are checked.

.html

Have a look.

作者: Wongjas 時間: 27-8-2013 19:42

http://
s736.photobucket.com/user/wongsaichung/media/DSC06344_zpsc3edf710.jpg.html

作者: hk_allen 時間: 27-8-2013 20:01

http://
s736.photobucket.com/user/wongsaichung/media/DSC06344_zpsc3edf710.jpg.html
Wongjas 發表於 27-8-2013 19:42

靚!

入埋會多D指教啦..

作者: sammykwan 時間: 27-8-2013 21:28

It's a bit tricky here. Indeed, it was my concerns too.

With ET55 and 8.5J, they have a 3mm spacer install to avoid rubbering and suspension.
All the way right and left are checked.

http://s736.phot ...
Wongjas 發表於 27-8-2013 19:42

that make more sense with 3mm spacer....

歡迎光臨 HK Macau Stepwgn Club (http://www.stepwgnhk.com/)